|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Micro Networks A Division of Integrated Device Technology 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S DESCRIPTION * * 140 MHz SAW bandpass filter with 16 MHz bandwidth in 13.3x6.5mm SMP. RoHS compliant. TYPICAL PERFORMANCE S11 S22 Horizontal : Vertical (from top) Frequency Magnitude Magnitude Phase Deviation Group Delay Deviation 5 10 1 10 200 MHz / div dB/div dB/div deg/div ns/div Input and Output Impedances Frequency Span : 100-180 MHz Wide Band Response Frequency Span : 0-500 MHz Vertical Scale : 10 dB/div IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 1 of 3 Micro Networks A Division of Integrated Device Technology 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S SPECIFICATION Parameter Center Frequency (Fc) 1 Insertion Loss 2 1 dB Bandwidth 3 dB Bandwidth 35 dB Bandwidth Passband Ripple 3 Phase Deviation from Linear 3 Group Delay Variation 3 Absolute Delay Ultimate Rejection 4 Substrate Temperature Coefficient of Frequency Ambient Temperature System Source and Load Impedance Notes: Min Typ Max Units 139.6 15 16 40 140 140.4 8.2 11 16.4 17.4 21.1 22 0.43 1 3 14 45 160 0.94 44 Lithium Niobate -90 25 50 MHz dB MHz MHz MHz dB p-p deg p-p ns p-p s dB ppm/C C 1. Average of the lower and upper 3 dB frequencies. 2. Average level in the passband. 3. Evaluated over 80% of the 3dB bandwidth (i.e. FC6.4 MHz). 4. Evaluated over the intervals 20 - 124 MHz and 156 - 280 MHz. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level DC Voltage Between Each Terminal Min -40 Max +85 +17 15 Units C dBm V MATCHING CIRCUIT 11 Input 50 Source Single Ended 5 Output 50 Load Single Ended 1,2,3,4,6, 7,8,9,10,12 Ls2 = 120 nH Cp2 = 0 pF (not used) Component values (minimum inductor Q = 45): Ls1 = 100 nH Cp1 = 33 pF Notes: 1. The component values shown above are those used in the Micro Networks test fixture. Optimum values may change depending on board layout. Cp2 may be a capacitor or an inductor. 2. 5% tolerance components or better are recommended. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 2 of 3 Micro Networks A Division of Integrated Device Technology 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S PACKAGE OUTLINE AND RECOMMENDED PCB LAYOUT PACKAGE INFORMATION RECOMMENDED PCB FOOTPRINT 15.37 ICS BA03114S YYJJJM 8.53 2.98 .89 2.54 2.54 7.62 2.59 Pin Configuration: 11 Input 12 Input Return 5 Output 6 Output Return All Others Ground NOTE: Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating Dimensions shown are all nominal in millimetres. All tolerances are 0.15 mm except overall length and width. ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. (c) 2005 All rights reserved. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 3 of 3 |
Price & Availability of SF0140BA03114S |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |